View B170PW06-V2_6583706.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

au optronics corporation b170pw06 v2 product specification document version 0 1/33 ( ) preliminary specifications ( v ) final specifications module 17.0 wxga+ color tft-lcd model name b170pw06 v2 customer date checked & approved by howard lee 2006/1/26 note: this specification is subject to change without notice. approved by date prepared by maxine lee 2006/1/26 nbbu marketing division / au optronics corporation www.datasheet.co.kr datasheet pdf - http://www..net/
au optronics corporation b170pw06 v2 product specification document version 0 2/33 contents 1. handling precautions..............................................................................................................4 2. general description.................................................................................................................5 2.1 general specification.........................................................................................................5 2.2 optical characteristics.......................................................................................................6 3. functional block diagram.....................................................................................................10 4. absolute maximum ratings..................................................................................................11 4.1 absolute ratings of tft lcd module..............................................................................11 4.2 absolute ratings of backlight unit...................................................................................11 4.3 absolute ratings of environment.....................................................................................11 5. electrical characteristics.......................................................................................................12 5.1 tft lcd module..............................................................................................................12 5.2 backlight unit...................................................................................................................14 6. signal characteristic.............................................................................................................16 6.1 pixel format image..........................................................................................................16 6.2 the input data format.......................................................................................................17 6.3 signal description............................................................................................................19 6.4 interface timing................................................................................................................20 6.5 power on/off sequence...............................................................................................22 7. connector description..........................................................................................................23 7.1 tft lcd module..............................................................................................................23 7.2 backlight unit...................................................................................................................23 7.3 signal for lamp connector...............................................................................................23 8. vibration and shock test......................................................................................................24 8.1 vibration test...................................................................................................................24 8.2 shock test spec:..............................................................................................................24 9. reliability................................................................................................................................25 10. mechanical characteristics.................................................................................................26 10.1 lcm outline dimension.................................................................................................26 10.2 screw hole depth and center position..........................................................................28 11. shipping and package.........................................................................................................29 11.1 shipping label format...................................................................................................29 11.2. carton package.............................................................................................................29 12. appendix: edid description................................................................................................30 www.datasheet.co.kr datasheet pdf - http://www..net/
au optronics corporation b170pw06 v2 product specification document version 0 3/33 record of revision version and date page old description new description remark v0 2006/11/30 initial edition www.datasheet.co.kr datasheet pdf - http://www..net/
au optronics corporation b170pw06 v2 product specification document version 0 4/33 1. handling precautions 1) since front polarizer is easily damaged, pay attention not to scratch it. 2) be sure to turn off power supply when inserting or disconnecting from input connector. 3) wipe off water drop immediately. long contact with water may cause discoloration or spots. 4) when the panel surface is soiled, wipe it with absorbent cotton or other soft cloth. 5) since the panel is made of glass, it may break or crack if dropped or bumped on hard surface. 6) since cmos lsi is used in this module, take care of static electricity and insure human earth when handling. 7) do not open nor modify the module assembly. 8) do not press the reflector sheet at the back of the module to any directions. 9) in case if a module has to be put back into the packing container slot after once it was taken out from the container, do not press the center of the ccfl reflector edge. instead, press at the far ends of the cfl reflector edge softly. otherwise the tft module may be damaged. 10) at the insertion or removal of the signal interface connector, be sure not to rotate nor tilt the interface connector of the tft module. 11) after installation of the tft module into an enclosure (notebook pc bezel, for example), do not twist nor bend the tft module even momentary. at designing the enclosure, it should be taken into consideration that no bending/twisting forces are applied to the tft module from outside. otherwise the tft module may be damaged. 12) cold cathode fluorescent lamp in lcd contains a small amount of mercury. please follow local ordinances or regulations for disposal. 13) small amount of materials having no flammability grade is used in the lcd module. the lcd module should be supplied by power complied with requirements of limited power source (iec60950 or ul1950), or be applied exemption. 14) the lcd module is designed so that the ccfl in it is supplied by limited current circuit (iec60950 or ul1950). do not connect the ccfl in hazardous voltage circuit. www.datasheet.co.kr datasheet pdf - http://www..net/
au optronics corporation b170pw06 v2 product specification document version 0 5/33 2. general description b170pw06 v2 is a color active matrix liquid crystal display composed of a tft lcd panel, a driver circuit, and backlight system. the screen format is intended to support the wxga+ (1440(h) x 900(v)) screen and 262k colors (rgb 6-bits data driver). all input signals are lvds interface compatible. inverter of backlight is not included. b170pw06 v2 is designed for a display unit of notebook style personal computer and industrial machine. 2.1 general specification the following items are characteristics summary on the table at 25 condition: items unit specifications screen diagonal [mm] 391 (17.0w ) active area [mm] 367.20(h) x 229.50(v) pixels h x v 1440x3(rgb)x900 pixel pitch [mm] 0.255x0.255 pixel arrangement r.g.b. vertical stripe display mode normally white white luminance (i ccfl =6.5ma) note: i ccfl is lamp current [cd/m 2 ] 220 typ. (5 points average) 200 min. (5 points average) (note1) luminance uniformity 1.2 max. (5 points) contrast ratio 500 typ optical rise time/fall time [msec] 8ms typ. (14ms max) nominal input voltage vdd [volt] +3.3 typ. (+3.0 min, +3.6 max) power consumption [watt] 7 typ (without inverter) weight [grams] 660 typ. (700 max) physical size [mm] typ: 382.2(w)x244.5(h)x6.4 (d) max:382.7(w)x245.0(h)x7.0 (d) electrical interface 2 channel lvds surface treatment glare, hard coating (3h) support color native 262k colors ( rgb 6-bit data driver) temperature range operating storage (non - operating) [ o c] [ o c] 0 to +50 - 20 to +60 rohs compliance rohs compliance www.datasheet.co.kr datasheet pdf - http://www..net/
au optronics corporation b170pw06 v2 product specification document version 0 6/33 2.2 optical characteristics the optical characteristics are measured under stable conditions at 25 (room temperature): item unit conditions min. typ. max. note white luminance i ccfl =6.5ma [cd/m 2 ] 5 points average 200 220 - 1, 4, 8 [degree] [degree] horizontal (right) cr = 10 (left) 40 40 45 45 - - viewing angle [degree] [degree] vertical (upper) cr = 10 (lower) 15 30 20 35 - - 7 luminance uniformity 5 points 1.2 1,3 luminance uniformity 13 points 1.5 2,3 cr: contrast ratio 400 500 - 4 cross talk % 4 5 [msec] rising - 2 5 [msec] falling - 6 9 response time [msec] rising + falling 8 14 6 red x 0.560 0.590 0.620 red y 0.315 0.345 0.375 green x 0.285 0.315 0.345 green y 0.525 0.555 0.585 blue x 0.125 0.155 0.185 blue y 0.125 0.155 0.185 white x 0.283 0.313 0.343 color / chromaticity coordinates (cie 1931) white y 0.299 0.329 0.359 2,7 www.datasheet.co.kr datasheet pdf - http://www..net/
au optronics corporation b170pw06 v2 product specification document version 0 7/33 note 1: 5 points position (display area : 367.20(h) x 229.50(v))mm) 1 2 3 4 5 h/4 h/4 h/4 h/4 h w w/4 w/4 w/4 w/4 note 2: 13 points position w/4 w w/4 h h/4 h/4 h/4 h/4 7 9 10 w/4 1 8 w/4 10 10 10 10 2 3 13 12 4 5 6 11 note 3: the luminance uniformity of 5 and 13 points is defined by dividing the maximum luminance values by the minimum test point luminance w13 = maximum brightness of thirteen points minimum brightness of thirteen points maximum brightness of five points w5 = minimum brightness of five points www.datasheet.co.kr datasheet pdf - http://www..net/
au optronics corporation b170pw06 v2 product specification document version 0 8/33 note 4: measurement method the lcd module should be stabilized at given temperature for 30 minutes to avoid abrupt temperature change during measuring. in order to stabilize the luminance, the measurement should be executed after lighting backlight for 30 minutes in a stable, windless and dark room. note 5 definition of cross talk (ct) ct = | y b C y a | / y a 100 (%) where y a = luminance of measured location without gray level 0 pattern (cd/m 2 ) y b = luminance of measured location with gray level 0 pattern (cd/m 2 ) center of the screen tft - lcd 50 cm photo detector lcd panel field=2 www.datasheet.co.kr datasheet pdf - http://www..net/
au optronics corporation b170pw06 v2 product specification document version 0 9/33 note 6: definition of response time: the output signals of bm-7 or equivalent are measured when the input signals are changed from black to white (falling time) and from white to black (rising time), respectively. the response time interval between the 10% and 90% of amplitudes. refer to figure as below. note 7. definition of viewing angle viewing angle is the measurement of contrast ratio R 10, at the screen center, over a 180 horizontal and 180 vertical range (off-normal viewing angles). the 180 viewing angle range is broken down as follows; 90 ( ) horizontal left and right and 90 ( ) vertical, high (up) and low (down). the measurement direction is typically perpendicular to the display surface with the screen rotated about its center to develop the desired measurement viewing angle. note 8. brightness measured with foxconn inverter t73i019.01, under 6.5ma lamp current input. signal(relative value) "black" tr tf "white" "white" 0% 10% 90% 100% www.datasheet.co.kr datasheet pdf - http://www..net/
au optronics corporation b170pw06 v2 product specification document version 0 10/33 3. functional block diagram the following diagram shows the functional block of the 17.0 inches wide color tft/lcd module: tft array/cell vdd lcd controller lcd drive card backlight unit 1440(r/g/b) x 3x900 gnd dc-dc converter ref circuit y-driver x-driver odd_ rxin0 odd_rxin1 odd_rxin2 odd_rxclkin (8 pairs lvds) jae fi-xb30sl-hf10 or compatible mating housing jae fi-x30h jst bhsr-02vs-1 lamp connector(2pin) even_ rxin0 even_rxin1 even_rxin2 even_rxclkin www.datasheet.co.kr datasheet pdf - http://www..net/
au optronics corporation b170pw06 v2 product specification document version 0 11/33 4. absolute maximum ratings absolute maximum rating of the module is as following: 4.1 absolute ratings of tft lcd module item symbol min max unit conditions logic/lcd drive vin -0.3 +4.0 [volt] note 1,2 4.2 absolute ratings of backlight unit item symbol min max unit conditions ccfl current iccfl - 7 [ma] rms note 1,2 4.3 absolute ratings of environment item symbol min max unit conditions operating temperature top 0 +50 [ o c] note 3 operation humidity hop 5 95 [%rh] note 3 storage temperature tst -20 +60 [ o c] note 3 storage humidity hst 5 95 [%rh] note 3 note 1: within ta (25 ) note 2: permanent damage to the device may occur if exceed maximum values note 3: for quality performance, please refer to auo iis(incoming inspection standard). twb=39 c operating range storage range -40 65 www.datasheet.co.kr datasheet pdf - http://www..net/
au optronics corporation b170pw06 v2 product specification document version 0 12/33 5. electrical characteristics 5.1 tft lcd module 5.1.1 power specification input power specifications are as follows; symble parameter min typ max units note vdd logic/lcd drive voltage 3.0 3.3 3.6 [volt] pdd vdd power 2.1 [watt] note 1 idd idd current 580 680 [ma] note 1 ,vdd=3.3 v i rush inrush current 2000 [ma] note 2 vddrp allowable logic/lcd drive ripple voltage 100 [mv] p-p note 1 : maximum measurement condition black pattern note 2 measure condition q3 ao6402 g d2 s d1 d5 d6 c3 0.01uf/25v c2 1uf/25v c1 1uf/16v q3 ao6402 g d2 s d1 d5 d6 f1 vr1 47k +12.0v vcc sw1 sw mag-spst 1 2 (lcd module input) (high to low) control signal r2 1k r2 1k r1 47k +3.3v 90% 10% vin rising time 0v 3.3v 0.5ms www.datasheet.co.kr datasheet pdf - http://www..net/
au optronics corporation b170pw06 v2 product specification document version 0 13/33 5.1.2 signal electrical characteristics input signals shall be low or high-impedance state when vdd is off. signal electrical characteristics are as follows; parameter condition min max unit vth differential input high threshold (vcm=+1.2v) 100 [mv] vtl differential input low threshold (vcm=+1.2v) -100 [mv] vcm differential input common mode voltage 1.1 1.45 [v] note: lvds differential voltage www.datasheet.co.kr datasheet pdf - http://www..net/
au optronics corporation b170pw06 v2 product specification document version 0 14/33 5.2 backlight unit parameter guideline for ccfl inverter parameter min typ max units condition white luminance 2250 2450 ? [cd/m 2 ] (ta=25 ) note 1 ccfl current(iccfl) 3.0 6.5 7.0 [ma] rms (ta=25 ) note 2 ccfl frequency (fccfl) 40 60 80 [khz] (ta=25 ) note 3,4 ccfl ignition voltage (vs) ? ? 1700 [volt] rms (ta= 0 ) note 5 ccfl ignition voltage(vs) ? ? 1310 [volt] rms (ta= 25 ) note 5 ccfl voltage (reference) 666 740 814 [volt] rms (ta=25 ) note 6 ccfl power consumption 2.22 4.8 5.2 [watt] (ta=25 ) note 6 ccfl set up time 1 ? ? [sec] note 1: typ are auo recommended design points. *1 all of characteristics listed are measured under the condition using the auo test inverter. *2 in case of using an inverter other than listed, it is recommended to check the inverter carefully. sometimes, interfering noise stripes appear on the screen, and substandard luminance or flicker at low power may happen. *3 in designing an inverter, it is suggested to check safety circuit very carefully. impedance of ccfl, for instance, becomes more than 1 [m ohm] when cfl is damaged. *4 generally, ccfl has some amount of delay time after applying kick-off voltage. it is recommended to keep on applying kick-off voltage for 1 [sec] until discharge. *5 ccfl discharge frequency must be carefully chosen so as not to produce interfering noise stripes on the screen. *6 reducing ccfl current increases ccfl discharge voltage and generally increases ccfl discharge frequency. so all the parameters of an inverter should be carefully designed so as not to produce too much leakage current from high-voltage output of the inverter. note 2: it should be employed the inverter which has duty dimming , if iccfl is less than 4ma. note 3: ccfl discharge frequency should be carefully determined to avoid interference between inverter and tft lcd. note 4: the frequency range will not affect to lamp life and reliability characteristics. www.datasheet.co.kr datasheet pdf - http://www..net/
au optronics corporation b170pw06 v2 product specification document version 0 15/33 note 5: ccfl inverter should be able to give out a power that has a generating capacity of over 1,430 voltage. lamp units need 1,400 voltage minimum for ignition. note 6: calculator value for reference (i ccfl v ccfl =p ccfl ) note 7: requirements for a system inverter design, which is intended to have a better display performance, a better power efficiency and a more reliable lamp, are following. it shall help increase the lamp lifetime and reduce leakage current. a. the asymmetry rate of the inverter waveform should be less than 10%. b. the distortion rate of the waveform should bewithin 2 10%. * inverter output waveform had better be more similar to ideal sine wave. www.datasheet.co.kr datasheet pdf - http://www..net/
au optronics corporation b170pw06 v2 product specification document version 0 16/33 6. signal characteristic 6.1 pixel format image following figure shows the relationship of the input signals and lcd pixel format. r g b r g b r g b r g b r g b r g b r g b r g b 1 2 1439 1440 1st line 900th line www.datasheet.co.kr datasheet pdf - http://www..net/
au optronics corporation b170pw06 v2 product specification document version 0 17/33 6.2 the input data format odd pair( 1st pixel input) g0 r5 r4 r3 r2 r1 r0 de vs hs b5 b4 b3 b2 b1 b0 g5 g4 g3 g2 g1 ck din1 din2 din3 even pair(2nd pixel input) g0 r5 r4 r3 r2 r1 r0 de vs hs b5 b4 b3 b2 b1 b0 g5 g4 g3 g2 g1 ck din1 din2 din3 signal name description r5 r4 r3 r2 r1 r0 red data 5 (msb) red data 4 red data 3 red data 2 red data 1 red data 0 (lsb) red-pixel data red-pixel data each red pixel's brightness data consists of these 6 bits pixel data. g5 g4 g3 g2 g1 g0 green data 5 (msb) green data 4 green data 3 green data 2 green data 1 green data 0 (lsb) green-pixel data green-pixel data each green pixel's brightness data consists of these 6 bits pixel data. b5 b4 b3 b2 b1 b0 blue data 5 (msb) blue data 4 blue data 3 blue data 2 blue data 1 blue data 0 (lsb) blue-pixel data blue-pixel data each blue pixel's brightness data consists of these 6 bits pixel data. rxclkin data clock the typical frequency is 48.2 mhz. the signal is used to strobe the pixel data and dsptmg signals. all pixel data shall be valid at the falling edge when the dsptmg signal is high. www.datasheet.co.kr datasheet pdf - http://www..net/
au optronics corporation b170pw06 v2 product specification document version 0 18/33 de display timing this signal is strobed at the falling edge of -dtclk. when the signal is high, the pixel data shall be valid to be displayed. vs vertical sync the signal is synchronized to -dtclk . hs horizontal sync the signal is synchronized to -dtclk . note: output signals from any system shall be low or hi-z state when vdd is off. www.datasheet.co.kr datasheet pdf - http://www..net/
au optronics corporation b170pw06 v2 product specification document version 0 19/33 6.3 signal description lvds is a differential signal technology for lcd interface and high speed data transfer device. pin no symbol function etc. 1 gnd ground 2 vdd power supply ,3.3 v (typical) 3 vdd power supply ,3.3 v (typical) 4 v edid ddc 3.3v power 5 nc no connection (reserved for auo) test 6 clk edid ddc clock 7 data edid ddc data 8 odd_rxin0- -lvds differential data input 9 odd_rxin0+ +lvds differential data input 10 gnd ground 11 odd_rxin1- -lvds differential data input 12 odd_rxin1+ +lvds differential data input 13 gnd ground 14 odd_rxin2- -lvds differential data input 15 odd_rxin2+ +lvds differential data input 16 gnd ground 17 odd_rxclkin- -lvds differential clock input 18 odd_rxclkin+ +lvds differential clock input 19 gnd ground 20 even_rxin0- -lvds differential data input 21 even_rxin0+ +lvds differential data input 22 gnd ground 23 even_rxin1- -lvds differential data input 24 even_rxin1+ +lvds differential data input 25 gnd ground 26 even_rxin2- -lvds differential data input 27 even_rxin2+ +lvds differential data input 28 gnd ground 29 even_rxclkin- -lvds differential clock input 30 even_rxclkin+ +lvds differential clock input www.datasheet.co.kr datasheet pdf - http://www..net/
au optronics corporation b170pw06 v2 product specification document version 0 20/33 note1: start from right side note2: please follow vesa standard. note3: input signals shall be low or high-impedance when vdd is off. internal circuit of lvds inputs are as following. the module uses a 100ohm resistor between positive and negative data lines of each receiver input 6.4 interface timing 6.4.1 timing characteristics basically, interface timings should match the 1440x900 manufacturing guide line timing. signal item symbol min typ max unit period tv 904 912 2048 th active tdisp(v) 900 900 900 th vertical section blanking tblk(v) 4 12 - th period th 760 880 1024 tclk active tdisp(h) 720 720 720 tclk horizontal section blanking tblk(h) 40 160 - tclk period tclk 16.61 20.75 - ns clock frequency@60hz freq - 48.2 60.2 mhz note : de mode only www.datasheet.co.kr datasheet pdf - http://www..net/
au optronics corporation b170pw06 v2 product specification document version 0 21/33 6.4.2 timing diagram www.datasheet.co.kr datasheet pdf - http://www..net/
au optronics corporation b170pw06 v2 product specification document version 0 22/33 6.5 power on/off sequence vdd power and lamp on/off sequence is as follows. interface signals are also shown in the chart. signals from any system shall be hi-z state or low level when vdd is off. power sequence timing value parameter min. typ. max. units t1 0.5 - 10 (ms) t2 0 - 50 (ms) t3 0 - 50 (ms) t4 500 - - (ms) t5 200 - - (ms) t6 200 - - (ms) t7 0 - 10 (ms) t4 t3 t2 t5 valid data t1 10% 90% 10% 90% t6 t 7 power supply vdd lvds interface backlight on www.datasheet.co.kr datasheet pdf - http://www..net/
au optronics corporation b170pw06 v2 product specification document version 0 23/33 7. connector description physical interface is described as for the connector on module. these connectors are capable of accommodating the following signals and will be following components. 7.1 tft lcd module connector name / designation for signal connector manufacturer jae or compatible type / part number fi-xb30sl-hf10 or compatible mating housing/part number fi-x30h mating contact/part number fi-xc3-1-15000 7.2 backlight unit physical interface is described as for the connector on module. these connectors are capable of accommodating the following signals and will be following components. connector name / designation for lamp connector manufacturer jst type / part number bhsr-02vs-1 mating type / part number sm02b-bhss-1-tb 7.3 signal for lamp connector pin # cable color signal name 1 red lamp high voltage 2 white lamp low voltage www.datasheet.co.kr datasheet pdf - http://www..net/
au optronics corporation b170pw06 v2 product specification document version 0 24/33 8. vibration and shock test 8.1 vibration test test spec: l test method: non-operation l acceleration: 1.5g l frequency: 10 - 500hz random l sweep: 30 minutes each axis (x, y, z) 8.2 shock test spec: test spec: l test method: non-operation l acceleration: 180 g , half sine wave l active time: 2 ms l pulse: x,y,z .one time for each side www.datasheet.co.kr datasheet pdf - http://www..net/
au optronics corporation b170pw06 v2 product specification document version 0 25/33 9. reliability items required conditions operating life C high temp. temp.= +50 c, dynamic. 250 hours, humidity 20% operating life C low temp. temp.= 0 c, dynamic, 250 hours, humidity 20% high temp. storage life C non-operating temp.= +60 c, non-operating, 250 hours , humidity 20% low temp. storage life C non-operating temp.= -20 c, non-operating, 250 hours high temp & high humidity operating life temp.=+40 c, dynamic humidity 95%(non-condensing), 250 hours shock C non-operating 180g, 2.0 ms, half sine wave vibration C non-operating random vibration, 1.5 g zero-to-peak, 10 to 500 hz, 30 minutes in each of three mutually perpendicular axes temp. cycle C non-operating -20 c to +60 c, ramp 20 c/min, duration at temp. = 30min, test cycles = 50 esd contact : 8kv/ operation air : 15kv / operation room temperature test 25 , 2000hours, operating with loop pattern note1: according to en61000-4-2 , esd class b: some performance degradation allowed. no data lost . self-recoverable. no hardware failures. note2: ccfl life time: 12,000 hours minimum under normal module usage. note3: mtbf (excluding the ccfl): 30,000 hours with a confidence level 90% www.datasheet.co.kr datasheet pdf - http://www..net/
au optronics corporation b170pw06 v2 product specification document version 0 26/33 10. mechanical characteristics 10.1 lcm outline dimension front view www.datasheet.co.kr datasheet pdf - http://www..net/
au optronics corporation b170pw06 v2 product specification document version 0 27/33 rear view www.datasheet.co.kr datasheet pdf - http://www..net/
au optronics corporation b170pw06 v2 product specification document version 0 28/33 10.2 screw hole depth and center position screw hole minimum depth, from side surface =2.8 mm (see drawing) screw hole center location, from front surface = 3.75 0.3mm (see drawing) screw maximum length = 2.5 mm (see drawing) screw torque: maximum2.5 kgzf-cm www.datasheet.co.kr datasheet pdf - http://www..net/
au optronics corporation b170pw06 v2 product specification document version 0 29/33 11. shipping and package 11.1 shipping label format 11.2. carton package packing is 20 pcs / box. firmware week code manufacturing area model name hardware control code www.datasheet.co.kr datasheet pdf - http://www..net/
au optronics corporation b170pw06 v2 product specification document version 0 30/33 12. appendix: edid description address function b170pw06 v2 value value note hex hex bin dec 00 header 00 00000000 0 01 ff 11111111 255 02 ff 11111111 255 03 ff 11111111 255 04 ff 11111111 255 05 ff 11111111 255 06 ff 11111111 255 07 00 00000000 0 08 eisa manuf. code lsb 06 00000110 6 09 compressed ascii af 10101111 175 0a product code 87 10000111 135 0b hex, lsb first 62 01100010 98 0c 32-bit ser # 00 00000000 0 0d 00 00000000 0 0e 00 00000000 0 0f 00 00000000 0 10 week of manufacture 01 00000001 1 11 year of manufacture 11 00010001 17 12 edid structure ver. 01 00000001 1 13 edid revision # 03 00000011 3 14 video input def. (digital i/p, non-tmds, crgb) 80 10000000 128 15 max h image size (rounded to cm) 25 00100101 37 16 max v image size (rounded to cm) 17 00010111 23 17 display gamma (=(gamma*100)-100) 78 01111000 120 18 feature support (no dpms, active off, rgb, tmg blk#1) 0a 00001010 10 19 red/green low bits (lower 2:2:2:2 bits) 1c 00011100 28 1a blue/white low bits (lower 2:2:2:2 bits) f5 11110101 245 1b red x (upper 8 bits) 97 10010111 151 1c red y/ higher 8 bits 58 01011000 88 1d green x 50 01010000 80 1e green y 8e 10001110 142 1f blue x 27 00100111 39 20 blue y 27 00100111 39 21 white x 50 01010000 80 22 white y 54 01010100 84 23 established timing 1 00 00000000 0 24 established timing 2 00 00000000 0 25 established timing 3 00 00000000 0 26 standard timing #1 01 00000001 1 www.datasheet.co.kr datasheet pdf - http://www..net/
au optronics corporation b170pw06 v2 product specification document version 0 31/33 27 01 00000001 1 28 standard timing #2 01 00000001 1 29 01 00000001 1 2a standard timing #3 01 00000001 1 2b 01 00000001 1 2c standard timing #4 01 00000001 1 2d 01 00000001 1 2e standard timing #5 01 00000001 1 2f 01 00000001 1 30 standard timing #6 01 00000001 1 31 01 00000001 1 32 standard timing #7 01 00000001 1 33 01 00000001 1 34 standard timing #8 01 00000001 1 35 01 00000001 1 36 pixel clock/10000 lsb 9e 10011110 158 37 pixel clock/10000 usb 25 00100101 37 38 horz active lower 8bits a0 10100000 160 39 horz blanking lower 8bits 40 01000000 64 3a horzact:horzblnk upper 4:4 bits 51 01010001 81 3b vertical active lower 8bits 84 10000100 132 3c vertical blanking lower 8bits 0c 00001100 12 3d vert act : vertical blanking (upper 4:4 bit) 30 00110000 48 3e horzsync. offset d0 11010000 208 3f horzsync.width 20 00100000 32 40 vertsync.offset : vertsync.width 36 00110110 54 41 horz&vert sync offset/width upper 2bits 00 00000000 0 42 horizontal image size lower 8bits 6f 01101111 111 43 vertical image size lower 8bits e5 11100101 229 44 horizontal & vertical image size (upper 4:4 bits) 10 00010000 16 45 horizontal border (zero for internal lcd) 00 00000000 0 46 vertical border (zero for internal lcd) 00 00000000 0 47 signal (non-intr, norm, no stero, sep sync, neg pol) 18 00011000 24 48 detailed timing/monitor 00 00000000 0 49 descriptor #2 00 00000000 0 4a 00 00000000 0 4b 0f 00001111 15 4c 00 00000000 0 4d 00 00000000 0 4e 00 00000000 0 4f 00 00000000 0 50 00 00000000 0 51 00 00000000 0 www.datasheet.co.kr datasheet pdf - http://www..net/
au optronics corporation b170pw06 v2 product specification document version 0 32/33 52 00 00000000 0 53 00 00000000 0 54 00 00000000 0 55 00 00000000 0 56 00 00000000 0 57 00 00000000 0 58 00 00000000 0 59 20 00100000 32 5a detailed timing/monitor 00 00000000 0 5b descriptor #3 00 00000000 0 5c 00 00000000 0 5d fe 11111110 254 5e 00 00000000 0 5f manufacture 41 01000001 65 a 60 manufacture 55 01010101 85 u 61 manufacture 4f 01001111 79 o 62 0a 00001010 10 63 20 00100000 32 64 00 00000000 0 65 20 00100000 32 66 20 00100000 32 67 20 00100000 32 68 20 00100000 32 69 20 00100000 32 6a 20 00100000 32 6b 20 00100000 32 6c detailed timing/monitor 00 00000000 0 6d descriptor #4 00 00000000 0 6e 00 00000000 0 6f fe 11111110 254 70 00 00000000 0 71 manufacture p/n 42 01000010 66 b 72 manufacture p/n 31 00110001 49 1 73 manufacture p/n 37 00110111 55 7 74 manufacture p/n 30 00110000 48 0 75 manufacture p/n 50 01010000 80 p 76 manufacture p/n 57 01010111 87 w 77 manufacture p/n 30 00110000 48 0 78 manufacture p/n 36 00110110 54 6 79 manufacture p/n 20 00100000 32 7a manufacture p/n 56 01010110 86 v 7b manufacture p/n 32 00110010 50 2 7c 20 00100000 32 www.datasheet.co.kr datasheet pdf - http://www..net/
au optronics corporation b170pw06 v2 product specification document version 0 33/33 7d 0a 00001010 10 7e extension flag 00 00000000 0 7f checksum 0b 00001011 11 sum 6400 www.datasheet.co.kr datasheet pdf - http://www..net/

▲Up To Search▲

Price & Availability of B170PW06-V2

	To Download B170PW06-V2 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .